CANTAC HIGH-TAC is a premium high strength, high heat resistant contact spray adhesive formulated for bonding High Pressure Laminates (HPL) to MDF, particleboard and plywood. HIGH-TAC is also suitable for a wide variety of substrates and applications including furniture and upholstery work, automotive headliners and marine applications. Superior bond strength properties and exceptional heat resistance make HIGH-TAC an excellent choice for permanent bonding of HPL and a variety of substrates.
COMMON USES
Bonds High Pressure Laminates (HPL)
Radius Edge Banding
Bonds Foam to Foam
Furniture & Upholstery
Automotive & Marine Headliners
Wall & Floor Coverings
BONDS
HIGH-TAC will effectively bond High Pressure Laminates (HPL), MDF, particleboard and plywood, urethane foam, FRP, carpet, felt, fabrics, paper products, duct insulation, steel, aluminium, concrete, moulded fiberglass, most plastics and many other materials.
ADVANTAGES
High Heat Resistant
High Strength
Fast Tacking
Non-Flammable
Waterproof
No Ozone Depleting Substances
Low Odour
High Coverage
High Solids
PREPARATION
For best results all surfaces to be bonded must be clean, dry and free from dirt, dust, oil, loose paint, wax and grease. The temperature of the adhesive and the surfaces being bonded should ideally be between 15°C - 27°C.
TECHNICAL DETAILS
Chemical Description: Solvent Based Contact Adhesive
Solids Content: 32 - 36%
Viscosity: Sprayable Grade
Minimum Open Time: 1 - 3 minutes
Maximum Open Time: 2 hours (best results within 1hr)
Heat Resistance: -40 – +120ºC
Cleaner: Citrus Cleaner or Acetone
Flash Point: Non detected
Specific Density: 1.20kg per ltr +/- 5%
APPLICATION METHOD
Sprayed through CANTAC brand Guns & Hoses
APPEARANCE
Clear Sprayable Liquid
ODOUR
Minimal Solvent Odour
CLEAN UP
Clean tip after use with CANTAC Citrus Cleaner. Excess adhesive and overspray may be removed with CANTAC Citrus Cleaner, Acetone, WOODLOK GLAZE-AWAY & DSOLV-AWAY, GLUE GURU 05CR or most Industrial Solvents.
LIMITATIONS
HIGH-TAC is not recommended for use on Polystyrene. HIGH-TAC is not recommended for Vinyl Flooring.
TESTING
Always test the suitability of the product for your application before use.
COVERAGE
15m2 per canister Single Sided (Guide only. Coverage depends on absorbency of surface and coating weight).
COMMON USES
HIGH-TAC will effectively bond High Pressure Laminates (HPL), MDF, particleboard and plywood, urethane foam, FRP, carpet, felt, fabrics, paper products, duct insulation, steel, aluminium, concrete, moulded fiberglass, most plastics and many other materials.
ADVANTAGES
For best results all surfaces to be bonded must be clean, dry and free from dirt, dust, oil, loose paint, wax and grease. The temperature of the adhesive and the surfaces being bonded should ideally be between 15°C - 27°C.
TECHNICAL DETAILS
Sprayed through CANTAC brand Guns & Hoses
APPEARANCE
Minimal Solvent Odour
CLEAN UP
Clean tip after use with CANTAC Citrus Cleaner. Excess adhesive and overspray may be removed with CANTAC Citrus Cleaner, Acetone, WOODLOK GLAZE-AWAY & DSOLV-AWAY, GLUE GURU 05CR or most Industrial Solvents.
LIMITATIONS
HIGH-TAC is not recommended for use on Polystyrene. HIGH-TAC is not recommended for Vinyl Flooring.
TESTING
Always test the suitability of the product for your application before use.
COVERAGE
15m2 per canister Single Sided (Guide only. Coverage depends on absorbency of surface and coating weight).
SIZES
TECHNICAL DATA SHEET SAFETY DATA SHEET